APPLICATIONS OF THE MOC3011 TRIAC DRIVER DOWNLOAD

These two chips are assembled in a 6 pin DIP package, providing 7. The detector chip is a complex device which functions in the same manner as a small triac, generating the signals necessary to drive the gate of a larger triac such as Fairchild s. This application note describes circuits in which these More information. In each More information. A standard value, ohm resistor can be used in practice for R1. Increasing demands for numerical control machines, robotics and technically advanced appliances More information.

Uploader: Shagami
Date Added: 5 March 2005
File Size: 70.38 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 62794
Price: Free* [*Free Regsitration Required]

Application Notes: TRIAC Driver Optocouplers

These families More information. The designer can therefore design the input apppications to supply 10 ma to the LED and still be sure of satisfactory operation over a long operating lifetime. In order to design a snubber properly, one should really know the power factor of the reactive load, which is defined as the cosine of the phase shift caused by the load.

rhe The designer can therefore design the input circuitry to supply 10 mA to the LED and still be applicatiosn of satisfactory operation over a long operating lifetime. To allow a safety margin and ensure long service life, the is actually tested to trigger at a value lower than the specified 10 ma input threshold current.

The LED is guaranteed by the specifications to trigger the detector into the on state when the current passing through the LED is equal to, or greater than the I FT max specification. To reduce system disturbances it is therefore essential More information.

  ELOAM PC CAMERA DRIVER DOWNLOAD

An example is shown in Figure 8. It offers numerous advantages. The resistor should be chosen to set the current into the LED to be a minimum of 10 mA but no more than 50 mA.

Increasing demands for numerical control machines, robotics and technically advanced appliances More information. On the simply connecte Assuming the forward drop to be 1. These phenomena exist on all industrial More information.

CMOS, for example, is specified to have only 0.

Application Notes

Safety, policy and warranty. Incandescent lamps can sometimes draw a peak current known as flashover which can be extremely high, and the triac should be protected by a fuse or rated high enough to sustain this current.

An example is shown in Figure 8. This is usually not a problem, except in unusually noisy environments, because the MOC and its triac will commute off at the next zero crossing of the line voltage, and most loads are not noticeably affected by an occasional single half-cycle of applied power.

Assuming the forward drop to be 1. To make this website work, we log user data and share it with processors. Of course, zero crossing can be generated within the micro-computer itself, but this requires considerable software overhead and usually just as much hardware to generate the zero-crossing timing signals. Increasing demands for numerical control machines, robotics and technically advanced appliances.

On the other hand, care should be taken to ensure that the maximum LED input current 50 ma is not exceeded or the lifetime of the may be shortened.

  LITE ON DVD ESAU108 DRIVER DOWNLOAD

In this case, it is possible the MOC and the associated triac thhe be triggered on. The triac snubber is dependent upon the triac and load used and will not be discussed here. Application note AC switch triggering with 3.

These output detector chips are designed to drive triacs controlling loads on and 0V AC power lines.

A 4-bit address code determines. The maximum surge current rating of the MOC sets the minimum value of R1 through the equation: The LH relays More information.

In practice, this fhe be a or ohm resistor. Description The SX is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay.

A Constant-current Source A Constant-current Source Frequently, such as when you want to measure temperature with a silicon diode, it is desirable to have a source of a reproducible, constant current. By using a, a triac, and a low voltage source, it is possible to control a large lighting load from a long distance through low voltage signal wiring which is completely isolated o the ac line. Such wiring usually is not required to be put in conduit, so the cost savings in installing a lighting applicaitons in commercial or residential buildings can be considerable.